Fredenslund workshop tools

{'type': 'object', 'properties': {'system': {'type': 'object', 'properties': {'gap_mm': {'type': 'integer', 'maximum': 200, 'minimum': 40, 'description': 'Gap between cleat boards (default = board_mm, as in the Fredenslund system); pitch = board + gap'}, 'board_mm': {'type': 'integer', 'maximum': 200, 'minimum': 40, 'description': 'Cleat board height (default 90). The gap equals the board unless gap_mm is given'}, 'buffer_mm': {'type': 'integer', 'maximum': 200, 'minimum': 10, 'description': 'Buffer between hangers and above the floor (default 30)'}, 'material_mm': {'type': 'integer', 'maximum': 40, 'minimum': 3, 'description': 'Material thickness (default 12)'}, 'tip_trim_mm': {'type': 'integer', 'maximum': 5, 'minimum': 0, 'description': 'Tip trim taken off the 45° bevel (default 1); changes finished sizes only'}, 'hook_plate_mm': {'type': 'integer', 'maximum': 120, 'minimum': 20, 'description': 'Hook plate incl. material (default 72); at most the gap − 3, so a hanger can be lifted off'}, 'bottom_limit_mm': {'type': 'integer', 'maximum': 2000, 'minimum': 0, 'description': 'The lowest cleat keeps its underside this far above the floor (default 210)'}, 'table_height_mm': {'type': 'integer', 'maximum': 2000, 'minimum': 0, 'description': 'Table height — the top of the table (default 900). The table hangs on a cleat table_offset_mm lower, and that cleat anchors the rows'}, 'table_offset_mm': {'type': 'integer', 'maximum': 1000, 'minimum': 0, 'description': "How far below the table height the table's own cleat has its top edge (default 60 = hook plate − material, so the tabletop hangs like a hanger; 0 makes the table height the top of a cleat)"}, 'top_clearance_mm': {'type': 'integer', 'maximum': 4000, 'minimum': 0, 'description': 'Clearance below the ceiling (default = the gap, 90); at least the hook plate + 3, so a hanger on the top row can be lifted off'}}, 'description': 'Override the Fredenslund system (all in mm). Leave out to use the defaults', 'additionalProperties': False}, 'hangers': {'type': 'array', 'items': {'type': 'object', 'required': ['x_mm', 'cleat_top_mm', 'width_mm'], 'properties': {'name': {'type': 'string', 'maxLength': 40, 'description': 'Optional name shown on the drawing and in the cut list (max 40 characters)'}, 'x_mm': {'type': 'integer', 'maximum': 7990, 'minimum': 0, 'description': "Left edge, mm from the wall's left edge (x + width at most 8000, the widest wall)"}, 'width_mm': {'type': 'integer', 'maximum': 8000, 'minimum': 10, 'description': 'Width in whole mm (the planner drags in 10 mm steps; the palette sizes are 50–550)'}, 'rows_below': {'type': 'integer', 'default': 0, 'maximum': 49, 'minimum': 0, 'description': 'Extra cleat rows spanned below the hook row (0 = one cleat; each adds one pitch, 180 mm, to the panel height). Typical: hooks 0; shelves and boxes 1 (a shelf hangs on its row and rests on the cleat below); deep boxes and panels 2; tall panels 3'}, 'cleat_top_mm': {'type': 'integer', 'maximum': 4000, 'minimum': 0, 'description': "Height from the floor of the top edge of the cleat the hanger hangs on; must be one of the wall's rows (300, 480, 660, 840, 1020, 1200 … 2280 with default settings)"}, 'extension_mm': {'type': 'integer', 'default': 0, 'maximum': 4000, 'minimum': 0, 'description': 'Extra panel length below the lowest cleat, mm (default 0)'}}, 'additionalProperties': False}, 'description': "Hangers to place. Each hangs on one cleat row, given by the height of that cleat's top edge from the floor"}, 'rows_off': {'type': 'array', 'items': {'type': 'integer', 'minimum': 0}, 'description': 'Cleat rows to switch off, by cleat top height from the floor'}, 'wall_width_mm': {'type': 'integer', 'default': 1220, 'maximum': 8000, 'minimum': 200, 'description': 'Wall width in mm (200–8000, default 1220 — a full plywood sheet)'}, 'wall_height_mm': {'type': 'integer', 'default': 2440, 'maximum': 4000, 'minimum': 300, 'description': 'Wall height in mm (300–4000, default 2440 — a full plywood sheet)'}}, 'additionalProperties': False}

{'type': 'object', 'required': ['width_mm', 'depth_mm'], 'properties': {'depth_mm': {'type': 'number', 'description': 'Desired top depth in mm; snaps to the nearest valid size (142–1966)'}, 'width_mm': {'type': 'number', 'description': 'Desired top width in mm; snaps to the nearest valid size (142–1966)'}, 'include_svg': {'type': 'boolean', 'default': False, 'description': 'Also return the SVG markup itself (2–15 KB). By default only the link to the SVG is returned'}, 'thickness_mm': {'type': 'number', 'default': 19, 'description': 'Board thickness in mm (default 19). Through cuts are encoded at thickness + 1 mm overcut'}, 'counterbore_mm': {'type': 'number', 'default': 6, 'description': 'Counterbore depth in mm for the Ø15 screw-hole rings (default 6; 0 omits them; never deeper than the thickness)'}}, 'additionalProperties': False}